Menu
Forum
What's new
New posts
Live Activity
Search forums
Members
Registered members
Classifieds Member Feedback
Car Audio Discussion
General Car Audio
Car Audio Build Logs
Car Audio Equipment
Subwoofers
Speakers
Amplifiers
Head Units
Car Audio Help
Wiring, Electrical and Installation
Enclosure Design & Construction
Car Audio Classifieds
Car Audio Classifieds
Car Audio Wanted
Classifieds Member Feedback
Gallery
New media
New comments
Search media
SHOP
Shop Head Units
Shop Amplifiers
Shop Speakers
Shop Subwoofers
Shop eBay Car Audio
Log in / Join
Test
Forum
Search
Search titles only
Search titles only
Log in / Join
Search
Search titles only
Search titles only
What's new
New posts
Live Activity
Search forums
Members
Registered members
Classifieds Member Feedback
Menu
Reply to thread
Forum
Car Audio Discussion
Car Audio Build Logs
2005 Ford Focus ZX4 Glove box subwoofer complete. 4/27/2024
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Message
<blockquote data-quote="just call me KeV" data-source="post: 8805585" data-attributes="member: 656095"><p>Back with a few more pictures of the kicks. I got a good seven hours in so I have made some progress..</p><p>This is the first sand I had done on the panels. No profiling yet. The carpet needs to be cleaned.</p><p>[ATTACH=full]41793[/ATTACH]</p><p></p><p>[ATTACH=full]41794[/ATTACH]</p><p></p><p>Fresh layer of tape. I typically need to redo the tape three times as it it is destroyed between coats. If I were a smarter man I would use a mold release.</p><p></p><p>[ATTACH=full]41795[/ATTACH]</p><p></p><p>You can see in this shot that they are not yet symmetrical. No biggie. We'll just build out the panel.</p><p></p><p>[ATTACH=full]41796[/ATTACH]</p><p></p><p>Extra material was added and the small gaps were filled.</p><p></p><p>[ATTACH=full]41797[/ATTACH]</p><p></p><p>There is a moderate amount of sanding on the panels to be done along with a finish coat. The passenger side needs the angle adjusted to better match the drivers side. So, I will end up hog-ing out some material so they have identical profiles.</p><p></p><p>[ATTACH=full]41801[/ATTACH]</p><p></p><p>The next few shots are closeups of both panels. The drivers side is much closer. It matches the contours of the vehicle rather nicely.</p><p></p><p>[ATTACH=full]41798[/ATTACH]</p><p></p><p>This second shot of the drivers' side brings up a conundrum. I think that I will end up bonding the fabbed kick and the plastic fatory panel. It will make it a pain in the but to wrap but I believe it will end up looking better.</p><p></p><p>[ATTACH=full]41799[/ATTACH]</p><p></p><p>Last shot is the passenger side. I am going to try to get as much done as I can tomorrow as it is going to be raining hardcore this weekend and I have a 4 hr. interview for a job on monday.</p><p></p><p>[ATTACH=full]41800[/ATTACH]</p></blockquote><p></p>
[QUOTE="just call me KeV, post: 8805585, member: 656095"] Back with a few more pictures of the kicks. I got a good seven hours in so I have made some progress.. This is the first sand I had done on the panels. No profiling yet. The carpet needs to be cleaned. [ATTACH type="full" alt="20220818_151727.jpg"]41793[/ATTACH] [ATTACH type="full" alt="20220818_160549.jpg"]41794[/ATTACH] Fresh layer of tape. I typically need to redo the tape three times as it it is destroyed between coats. If I were a smarter man I would use a mold release. [ATTACH type="full" alt="20220818_162955.jpg"]41795[/ATTACH] You can see in this shot that they are not yet symmetrical. No biggie. We'll just build out the panel. [ATTACH type="full" alt="20220818_164643_HDR.jpg"]41796[/ATTACH] Extra material was added and the small gaps were filled. [ATTACH type="full" alt="20220818_180712_HDR.jpg"]41797[/ATTACH] There is a moderate amount of sanding on the panels to be done along with a finish coat. The passenger side needs the angle adjusted to better match the drivers side. So, I will end up hog-ing out some material so they have identical profiles. [ATTACH type="full" alt="20220818_184521_HDR.jpg"]41801[/ATTACH] The next few shots are closeups of both panels. The drivers side is much closer. It matches the contours of the vehicle rather nicely. [ATTACH type="full" alt="20220818_184206.jpg"]41798[/ATTACH] This second shot of the drivers' side brings up a conundrum. I think that I will end up bonding the fabbed kick and the plastic fatory panel. It will make it a pain in the but to wrap but I believe it will end up looking better. [ATTACH type="full" alt="20220818_184212_HDR.jpg"]41799[/ATTACH] Last shot is the passenger side. I am going to try to get as much done as I can tomorrow as it is going to be raining hardcore this weekend and I have a 4 hr. interview for a job on monday. [ATTACH type="full" alt="20220818_184246.jpg"]41800[/ATTACH] [/QUOTE]
Insert quotes…
Verification
Post reply
Forum
Car Audio Discussion
Car Audio Build Logs
2005 Ford Focus ZX4 Glove box subwoofer complete. 4/27/2024
Top
Menu
Home
Refresh