Menu
Forum
What's new
New posts
Live Activity
Search forums
Members
Registered members
Classifieds Member Feedback
Car Audio Discussion
General Car Audio
Car Audio Build Logs
Car Audio Equipment
Subwoofers
Speakers
Amplifiers
Head Units
Car Audio Help
Wiring, Electrical and Installation
Enclosure Design & Construction
Car Audio Classifieds
Car Audio Classifieds
Car Audio Wanted
Classifieds Member Feedback
Gallery
New media
New comments
Search media
SHOP
Shop Head Units
Shop Amplifiers
Shop Speakers
Shop Subwoofers
Shop eBay Car Audio
Test
Forum
Search
Search titles only
Search titles only
Log in / Join
Search
Search titles only
Search titles only
What's new
New posts
Live Activity
Search forums
Members
Registered members
Classifieds Member Feedback
Menu
Reply to thread
Forum
Car Audio Discussion
Car Audio Build Logs
2016 Subaru Forester 2.0XT
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Message
<blockquote data-quote="AnthonyO" data-source="post: 8652951" data-attributes="member: 563887"><p>Doing this slowly but surely. Want to make sure I make NO mistakes whatsoever. </p><p></p><p>1 Skar RP800.1</p><p></p><p>1 Skar SDR12d2</p><p></p><p>1 6" Crossflow fan</p><p></p><p>1 NVX Ground Distribution and 1 NVX fused power distribution</p><p></p><p>Utilizing factory head-unit thru an AudioControl LC2i</p><p></p><p>Yesterday I installed the amp, fan, LC2i, and distribution blocks. Since they are on Styrofoam bracing was added to the bottom. </p><p></p><p>Today I ran 4 gauge OFC NVX wire from the amp to distribution blocks. Power and ground from the distribution blocks to the LC2i. Remote out from the LC2i to the amp and fan. And the streetwires RCA's from LC2i to amp.</p><p></p><p>Just have to run the 2/0 Excelene to the power distribution and 2/0 Excelene ground to distribution. Then pull the head-unit and plug in my jumper harness. Run the speaker wire and accessory wire from the jumper harness back to the LC2i. Run my 10 gauge OFC speaker wire to the enclosure and I am done. Probably finish some time next week while I am on vacation.</p><p></p><p>[ATTACH]262[/ATTACH]</p><p></p><p>[ATTACH]263[/ATTACH]</p><p></p><p>[ATTACH]264[/ATTACH]</p><p></p><p>[ATTACH]265[/ATTACH]</p><p></p><p>[ATTACH]266[/ATTACH]</p></blockquote><p></p>
[QUOTE="AnthonyO, post: 8652951, member: 563887"] Doing this slowly but surely. Want to make sure I make NO mistakes whatsoever. 1 Skar RP800.1 1 Skar SDR12d2 1 6" Crossflow fan 1 NVX Ground Distribution and 1 NVX fused power distribution Utilizing factory head-unit thru an AudioControl LC2i Yesterday I installed the amp, fan, LC2i, and distribution blocks. Since they are on Styrofoam bracing was added to the bottom. Today I ran 4 gauge OFC NVX wire from the amp to distribution blocks. Power and ground from the distribution blocks to the LC2i. Remote out from the LC2i to the amp and fan. And the streetwires RCA's from LC2i to amp. Just have to run the 2/0 Excelene to the power distribution and 2/0 Excelene ground to distribution. Then pull the head-unit and plug in my jumper harness. Run the speaker wire and accessory wire from the jumper harness back to the LC2i. Run my 10 gauge OFC speaker wire to the enclosure and I am done. Probably finish some time next week while I am on vacation. [ATTACH]262._xfImport[/ATTACH] [ATTACH]263._xfImport[/ATTACH] [ATTACH]264._xfImport[/ATTACH] [ATTACH]265._xfImport[/ATTACH] [ATTACH]266._xfImport[/ATTACH] [/QUOTE]
Insert quotes…
Verification
Post reply
Forum
Car Audio Discussion
Car Audio Build Logs
2016 Subaru Forester 2.0XT
Top
Menu
Home
Refresh