Menu
Forum
What's new
New posts
Live Activity
Search forums
Members
Registered members
Classifieds Member Feedback
Car Audio Discussion
General Car Audio
Car Audio Build Logs
Car Audio Equipment
Subwoofers
Speakers
Amplifiers
Head Units
Car Audio Help
Wiring, Electrical and Installation
Enclosure Design & Construction
Car Audio Classifieds
Car Audio Classifieds
Car Audio Wanted
Classifieds Member Feedback
Gallery
New media
New comments
Search media
SHOP
Shop Head Units
Shop Amplifiers
Shop Speakers
Shop Subwoofers
Shop eBay Car Audio
Log in / Join
Test
Forum
Search
Search titles only
Search titles only
Log in / Join
Search
Search titles only
Search titles only
What's new
New posts
Live Activity
Search forums
Members
Registered members
Classifieds Member Feedback
Menu
Reply to thread
Forum
Car Audio Help
Enclosure Design & Construction
Need help Astro Van wall build
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Message
<blockquote data-quote="outtherecustoms" data-source="post: 7456262" data-attributes="member: 625155"><p>4 warhorses 1 to each sub full tilt (may change to some heavily modded sundown nightshades built up by jacob). no as far as the wall it will be solid 2x4 cage with 8 layer face and rear wall with 4-5 layer thick sides. the interior will have 4 or 6" pvc cut down and mitered in in the corners (also am doing chop mat on each side for strength). 4 layers of resin will be applied to interior and 80 grit after each layer final layer 80 grit working to 220 grit. i want to paint it but what kind of paint works best? also face will be 6" thick the port side (next to subs) will be angled to fit snug inside of 6" pvc and fully glassed over. on the drivers side of port mdf will flare out to the b pillar to make up for outside wall length between it and the side. it will be fully rounded smoothed and resined (if needed pvc will be used for max flow. there will be 0 square corners in the box and no sharp edges. the cabin in front of b pillar is to remain stock with exception of deadening. also i was thinking of using some rattle trap xxx i have laying around to cover the face as i have seen this works good....the box will be tuned right around 70hz but im having a hard time for some reason figuring the tuning out exactly....i will have the van back on saturday here to say and will get full measurements. also chris fish (colorado-runs trunk 0-1000 USACI and going for record in it this year-and highest TL score ever.....shattered 3 sensers in port wars with 182.8) said to go about 12" deep on sub side and 14" deep on drivers side and make port as wide and tall as possible. he says i should be really close. i was thinking of doing face sides and top/bottom and taking a single mdf sheet and throwing in as temp plate for rear and testing to get proper depth but this will mess me up bad with my design as my rear will be going in before face on how i want to build it</p></blockquote><p></p>
[QUOTE="outtherecustoms, post: 7456262, member: 625155"] 4 warhorses 1 to each sub full tilt (may change to some heavily modded sundown nightshades built up by jacob). no as far as the wall it will be solid 2x4 cage with 8 layer face and rear wall with 4-5 layer thick sides. the interior will have 4 or 6" pvc cut down and mitered in in the corners (also am doing chop mat on each side for strength). 4 layers of resin will be applied to interior and 80 grit after each layer final layer 80 grit working to 220 grit. i want to paint it but what kind of paint works best? also face will be 6" thick the port side (next to subs) will be angled to fit snug inside of 6" pvc and fully glassed over. on the drivers side of port mdf will flare out to the b pillar to make up for outside wall length between it and the side. it will be fully rounded smoothed and resined (if needed pvc will be used for max flow. there will be 0 square corners in the box and no sharp edges. the cabin in front of b pillar is to remain stock with exception of deadening. also i was thinking of using some rattle trap xxx i have laying around to cover the face as i have seen this works good....the box will be tuned right around 70hz but im having a hard time for some reason figuring the tuning out exactly....i will have the van back on saturday here to say and will get full measurements. also chris fish (colorado-runs trunk 0-1000 USACI and going for record in it this year-and highest TL score ever.....shattered 3 sensers in port wars with 182.8) said to go about 12" deep on sub side and 14" deep on drivers side and make port as wide and tall as possible. he says i should be really close. i was thinking of doing face sides and top/bottom and taking a single mdf sheet and throwing in as temp plate for rear and testing to get proper depth but this will mess me up bad with my design as my rear will be going in before face on how i want to build it [/QUOTE]
Insert quotes…
Verification
Post reply
Forum
Car Audio Help
Enclosure Design & Construction
Need help Astro Van wall build
Top
Menu
Home
Refresh