Menu
Forum
What's new
New posts
Live Activity
Search forums
Members
Registered members
Classifieds Member Feedback
Car Audio Discussion
General Car Audio
Car Audio Build Logs
Car Audio Equipment
Subwoofers
Speakers
Amplifiers
Head Units
Car Audio Help
Wiring, Electrical and Installation
Enclosure Design & Construction
Car Audio Classifieds
Car Audio Classifieds
Car Audio Wanted
Classifieds Member Feedback
Gallery
New media
New comments
Search media
SHOP
Shop Head Units
Shop Amplifiers
Shop Speakers
Shop Subwoofers
Shop eBay Car Audio
Log in / Join
Test
Forum
Search
Search titles only
Search titles only
Log in / Join
Search
Search titles only
Search titles only
What's new
New posts
Live Activity
Search forums
Members
Registered members
Classifieds Member Feedback
Menu
Reply to thread
Forum
Car Audio Equipment
Amplifiers
Old school Alphasonik PMA2100 (2ch x100W) Want to run one sub, but no bridge switch?
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Message
<blockquote data-quote="ScottK" data-source="post: 8313736" data-attributes="member: 663052"><p>[ATTACH]26550304[/ATTACH][ATTACH]26550305[/ATTACH]</p><p></p><p>Hi all, new here and have searched but not really found anything about this question:</p><p></p><p>I have an old Alphasonik PMA-2100 amp I would like to run on a single Pioneer TS-W304R subwoofer. Not a lot of space available so I’m going with a single just to add some nice bottom. Vehicle is a 2009 Toyota Prius,( ok laugh all ya want I’m getting amazing MPG’s) the stock system (non-JBL) sounds OK, but some punchy bass would help. I have an hour long drive to and from work so I listen to a lot of music!</p><p></p><p>The amp has high and low inputs so I am planning on using the high inputs from the rear speakers.</p><p></p><p>If you will look at the images, the specs state it will run in mono, 200 watts into 4 or 8 ohm. There is no bridge switch on the amp, only wires, RCA inputs and a gain control. How do I wire this to run the single sub?</p><p></p><p>Next question will be high and low pass filters, but I gotta get the amp sorted out first.</p><p></p><p>Thanks!</p></blockquote><p></p>
[QUOTE="ScottK, post: 8313736, member: 663052"] [ATTACH=CONFIG]26550304[/ATTACH][ATTACH=CONFIG]26550305[/ATTACH] Hi all, new here and have searched but not really found anything about this question: I have an old Alphasonik PMA-2100 amp I would like to run on a single Pioneer TS-W304R subwoofer. Not a lot of space available so I’m going with a single just to add some nice bottom. Vehicle is a 2009 Toyota Prius,( ok laugh all ya want I’m getting amazing MPG’s) the stock system (non-JBL) sounds OK, but some punchy bass would help. I have an hour long drive to and from work so I listen to a lot of music! The amp has high and low inputs so I am planning on using the high inputs from the rear speakers. If you will look at the images, the specs state it will run in mono, 200 watts into 4 or 8 ohm. There is no bridge switch on the amp, only wires, RCA inputs and a gain control. How do I wire this to run the single sub? Next question will be high and low pass filters, but I gotta get the amp sorted out first. Thanks! [/QUOTE]
Insert quotes…
Verification
Post reply
Forum
Car Audio Equipment
Amplifiers
Old school Alphasonik PMA2100 (2ch x100W) Want to run one sub, but no bridge switch?
Top
Menu
Home
Refresh