Recent content by Chowder Head

^****it to holy hell!!!!!! Now I'm a little pissed.... The only thing that helps a little is that with shipping, that would of been $121.36. Still a little cheaper but nothing too crazy. Boris, I just basically selected one off of this ebay page for $154.00...

Boom, SE12" ordered. Final price was $138.60, not too bad. So it looks like I'll just have someone build it locally. Does anyone know a ballpark figure I should be looking to pay for a ported box, given the parameters of this particular sub? Thanks again everyone for the great help!

Well I measured my trunk area before and I thought I couldn't mange a ported 12". Now when I look at it, I might. Granted, I don't want to devote my entire trunk to the sub but I think it could be done. I dug up some measurements I took when I measured my trunk area and the max I could do is a...

Hey guys. After some heavy research, I'm just about sold on the SE series. Now the question that I cannot for the life of my figure out is if I want to go with a ported 10", or a sealed 12". Normally I'd lean towards porting it as I've heard it's not just for "heavy bass" but I hear the SE...

So I'm guessing to use the front AUX, the front plate has to be open? That *****, I was hoping I could see the lights and ish from the HU. Oh well, can't have it all. And FWIW, here's the 2.5mm male 3.5mm female connector I got. $0.95 shipped: http://www.dealextreme.com/details.dx/sku.2648

$10 you say? Would you happen to know a part number or a link to one? And yeah, the manual says the 2.5mm plug in the front is AUX 1. I did see a 3.5mm plug in the back, but I believe that's for a wired remote or something. However, the unit is placed all the way in, so I could just plug an aux...

Hey guys, I finally fired up my first system today and not only am I pleased to see everything works. I was also very impressed at the 880PRS. Quite a sexy unit! I just had one question. For those that have this head unit, or just know, is it possible to use the front aux for a portable MP3...

LOL, that would make a lot of sense. Why didn't I think about that, haha. I guess I tend to make things seem much harder than what they appear, haha. Ok so I have the settings down, now about the amp. To add with the HI OFF confusion, I also have another question about it. On the amp itself, I...

Bump...anybody? I've heard 80hz-2.5khz is a good place to start with for the Mach 5's but I'm clueless on what I should start the tweets at and I'm still stuck on the amp HI and OFF settings. Thanks!

Thanks for the replies guys! I have everything hooked up and will finally first this newly installed audio for the first time! Yeah, I'm a bit excited, can you tell? I just have three last final questions if you guys don't mind helping me once again. 1. My Kicker amp has a setting that is...

Hey guys, you may remember me from previous threads. Well I'm finally installing everything I've purchased (check the sig). I already installed the RAAMat on the doors and floor and now I'm running the wire before I put the carpet and the interior pieces back on. I just had a few questions that...

Holy ****! I just put the above strip in the freezer and in only like half a minute, I can completely peel it off! Sweet! Now I just gotta find a way to stick the entire roll in there, haha. Or at least a bunch of small strips. Thanks again for cold recommendation guys!

^Hmmm....interesting. If it doesn't loosen up after the end of the day, I'll have to try that. Thanks fellas! I don't think I am, lol. When I read your reply I was like holy crap....don't tell me I missed something obvious, ha. But when I went out and tried again I met the same results. Here's...

My interior is already stripped and am trying to apply some RAAMat to the doors and floor but I have a problem. I've been trying to peel the back layering off the sound deadener but it's still very much stuck to the back of it. All I heard that was required to apply sound deadener was pretty...

Bump for clarification.