Not sure you are going find anything smaller that I can think of. Width wise and length
This is the one I used in the neighbors truck. Looks like it would fit fine just above the amps your opening pic , or if you could raise the amps and place flat against/on the wall at the bottom?
COMPETITION GRADE DUAL MINI MIDI ANL FUSE HOLDER CAR AMP INSTALL 0 2 4 GAUGE NEW | eBay
Dual Gold Mini (MIDI) ANL Fuse Holder. Utilizes Mini ANL fuses (also known as MIDI fuses). Includes TWO high quality XScorpion mini ANL with LED indicator - you choose the size! Includes patented adapter rings (One 0 to 2 gauge and Two 4 to 8 gauge adapters).
Last edited:
Could you use an L-bracket and tape or screw it under the lip? The fuses facing the amps would be the best orientation.
Im looking at this pic thinking id look at raising those amps upward right at the lower portion of the(- connection of the sub wire connection and place it under the amplifiers. id move the shorter amp in the large amp location. all speaker wiring on the top areas and the power and grounds and remote @ the under area of the amps. would be plenty of room then. all speaker wiring can be zip tied neatly at the top. Thats me though
OP
AnthonyO
10+ year member
Budget Banger Connoisseur
- Thread Starter
- #23
Damned good idea. I could raise them 2” and have plenty of room.
I just bought these today
Fuse Distribution Block 2 Way 4 to 8 Gauge Out
Buy 2 Way Mini-ANL 4 to 8 Gauge Output Fuse Distribution Block. KnuKonceptz Includes Your Choice of Fuses Ranging from 20A to 150A with Purchase
www.knukonceptz.com
Man. I think so. The small 4-(2) 8 ga mini anl fuse holder should be able to fit just under the smaller amp after raised and mount to the wall just fine and supply both amps with a short power supply run from the anl fuse holder... less than a ft of supply wiring maybe??> daisy the remote from amp to amp too. I would think that smaller amp would be the sub amp? not sure but sub speaker wiring would be short too and nice and snugg/clean.
Thats what Im looking at? Its not my ride though,LOLNice price on that man. Fuses included. Sweet!!Damned good idea. I could raise them 2” and have plenty of room.
I just bought these today
They should be here by the weekendFuse Distribution Block 2 Way 4 to 8 Gauge Out
Buy 2 Way Mini-ANL 4 to 8 Gauge Output Fuse Distribution Block. KnuKonceptz Includes Your Choice of Fuses Ranging from 20A to 150A with Purchase
OP
AnthonyO
10+ year member
Budget Banger Connoisseur
- Thread Starter
- #26
Smaller amp is the 200.4Man. I think so. The small 4-(2) 8 ga mini anl fuse holder should be able to fit just under the smaller amp after raised and mount to the wall just fine and supply both amps with a short power supply run from the anl fuse holder... less than a ft of supply wiring maybe??> daisy the remote from amp to amp too. I would think that smaller amp would be the sub amp? not sure but sub speaker wiring would be short too and nice and snugg/clean.
Bigger amp is the mono
I was just looking at those .. Lol
OP
AnthonyO
10+ year member
Budget Banger Connoisseur
- Thread Starter
- #29
So my ADD kicked in last night and I couldn’t go to sleep until 3am. But during my ADD episode I think I figured out my amp rack without elevating the rack.
The module that’s in the way is the remote start module. And it’s held down by four bolts. If I move the module I open up another 6” of amp rack possibility. Meaning I can place my distribution blocks there. It also means that the original amp rack can expand by another inch or two.
A rough drawing
The module that’s in the way is the remote start module. And it’s held down by four bolts. If I move the module I open up another 6” of amp rack possibility. Meaning I can place my distribution blocks there. It also means that the original amp rack can expand by another inch or two.
A rough drawing
Id run what you have. Give it a chance/try to incorporate what you have. No since in spending funds on other gear without giving it a run/try? Thats me though. you can always change and or try other gear later. I like a dedicated sub amp and mids and highs amp myself.
Activity
No one is currently typing a reply...
Similar threads
Ahhh, I had it in my head that it was 1 ohm stable for some reason.
- Started by FuelEmpire
- General Car Audio 2 3
Could not tell you, but you may want to start by going to crutchfield and get a consensus on the 7 or so replacements they recommend. That average...
- Started by S550 GT
- Subwoofers
Ok so I started my install . I am doing it in stages so I am not without music for a week or two . I started by building and mounting the Amp...
- Started by azmandella
- General Car Audio
Crutchfield can tell you what speaker will fit your car.
for subs, Image Dynamics and Adire are still around. my last sub i bought was from...
- Started by swinger
- General Car Audio
I know there is a December sale at
mclaudio.ca
- Started by Popwarhomie
- General Car Audio 2 3 4
About this thread
New threads
-
How To Tell if Amp is drawing power when car is offHere is my situation: I recently had a sound system upgrade...
- Started by zoltman1991
- Replies: 3
-
Recommendations For Head Unit and Sub AmpI haven’t installed a car stereo in 20 years. My teenage...- Started by False Prophet
- Replies: 2
-
Battery Died Shortly Following Installation of SystemHello All! Here's my situation for my 2020 Lexus ES350. I...
- Started by zoltman1991
- Replies: 1
-
2017 Jeep Renegade Dash Mount TweetersI replaced the oem tweeters in my renegade with Pyle two way...
- Started by Djchill
- Replies: 1
-
Low Aux Input Volume?What is the minimum input voltage to drive the 'Aux In' on a...
- Started by jjsva2955
- Replies: 2