Recent content by Justinh722

Yea I heard that vibration is a major concern for these amps. It would probably be pretty easy to modify the board so It wouldn't move. I think I'll stick with the AP amp though. Not sure why their MSRP is 1,075 on their site. Seems a little ridiculous for that 2200.1. The only reason I...

Thanks guys. I think I'll just stick with this audiopipe. I know these are solid amps for the money. I have been running and recommending them for a while now. I just figured the better deal was the one that I could maybe sell for more if I decided to go bigger.

I currently own an AP 3001d that I'm running on two 12 inch HDC 12's. I have a chance to pick up a CT sounds 2200.1 in new condition, barely used, for only 250. I'm sure I can sell this AP amp for 300 to a buddy. I know CT sounds rate their amps at 12.8 volts, so I know this amp is underrated...

I got a hook up on two 15 inch TSNS subs from t3 audio. Anyone know what they are worth? How would one compare to a sundown zv4 or some zcons or death penaltys? The zv4 is 1.8k rms while the TSNS is a 4 inch coil at 5k RMS. I know the zv4 can take more power, but will the T3 subs shine...given...

I'm building a large box for two 18s for the trunk of a cadillac. The box is gonna be 9 cubes net with a 9 inch wide port. With the port being so wide and the side of the box acting as the port wall, it seems like it will need to be braced. Can I use a piece of mdf and split the port directly...

Then go ahead and tune to 32 hz. I would have went with the hds series if u aren't concerned much with loudness. Sound quality is a little better as well as the frequency response. Your sub will play well around the tuning frequency so go ahead and tune to 32 hz. U won't be disappointed. I like...

I say tune to 35. Those hdc's don't like the lows as much as the hds's. 35 will put u in the middle and give u good low output while getting loud. Sent from my SM-G900R4 using Tapatalk

I have been calculating boxes using torres and I wondered if torres factored in end correction when bending a port so I did a search on google. Reading through his post on SMD, I searched end correction within the post and found this. Torres - "when doing a slot port...just check the slot port...

Somehow I quoted my own text trying to edit it. Not sure how to delete it with tapatalk. Sent from my SM-G900R4 using Tapatalk

Sent from my SM-G900R4 using Tapatalk

Everything looks good. I don't think I have heard of anyone else trying this combo out. Coil fits perfect in the motor. I'll just give the ca glue a try. I have heard of people using black rtv silicone for caps. I used a hot air gun to remove the soft parts. Worked good. I didn't damage the...

I'm running two HDS312d2's on an audiopipe 3k amp and they are taking it like a champ. My box is 4.3 cubes tuned to 33 hertz. Only a little over 50 sq inches of port area and they are super loud. I keep breaking tabs off my interior cover pieces that I have to plastic weld back on. Just built a...

He said he lost the guys number. Granted he only picked the sub up for 140 bucks, but still. It was a Craigslist transaction. At least I get to try my hand at building a Frankenstein sub.

Had a problem with a shifted pole piece and shifted magnet on an HDC18 so I decided to use a spare FI BL motor that I had sitting around. The motor had a little surface rust on it from some moisture, is there something I could use to clean it off? Is it a big problem? I was also wondering about...

My buddy picked up an older model Audioque HDC18d2. I built him a box around 6.2 cubes tuned to 35 hz because he planned to run it in a mini van. Gave this monster some juice and it played decent at low volume. Sounded ok with sub up port back. Decided to turn the volume up a bit more and the...