NFrazier 10+ year member
Senior VIP Member
Products that are being installed:
![](/proxy.php?image=http%3A%2F%2Fimagizer.imageshack.us%2Fv2%2F280x200q90%2F822%2Fqtya.jpg&hash=5a39693ed01aaf642fcc5a8a209be5fe)
Mounted the fuse holder to the factory battery bracket. The power wire was loomed and heat shrunk to be as stealth as possible.
![](/proxy.php?image=http%3A%2F%2Fimagizer.imageshack.us%2Fv2%2F280x200q90%2F819%2Ftonc.jpg&hash=f42b1dbf28ec0682d74cfe3ac61db916)
![](/proxy.php?image=http%3A%2F%2Fimagizer.imageshack.us%2Fv2%2F280x200q90%2F843%2Fnede8.jpg&hash=b030044f54ebe0b085494b341d91a84c)
![](/proxy.php?image=http%3A%2F%2Fimagizer.imageshack.us%2Fv2%2F280x200q90%2F822%2Fqfoz.jpg&hash=019a5164872ea3b0da1faf983808b99b)
![](/proxy.php?image=http%3A%2F%2Fimagizer.imageshack.us%2Fv2%2F280x200q90%2F840%2Fd3y1.jpg&hash=44a3f64b24720178cdaf967c1e536e55)
Next I ran all of the wiring following factory harnesses on each side. The wires were zip-tied approximately every 6". The power wire was ran through a gromnet I installed where the factory clutch would normally be.
![](/proxy.php?image=http%3A%2F%2Fimagizer.imageshack.us%2Fv2%2F280x200q90%2F840%2Fc1e6.jpg&hash=4d0ff8b3bbbcf23895d79657170d0103)
![](/proxy.php?image=http%3A%2F%2Fimagizer.imageshack.us%2Fv2%2F280x200q90%2F855%2Fnxn5.jpg&hash=d9de973794e80e7eba2be91cc1735011)
![](/proxy.php?image=http%3A%2F%2Fimagizer.imageshack.us%2Fv2%2F280x200q90%2F850%2Fcicj.jpg&hash=8fe72b9bd4bc101d377e0094580e2e56)
![](/proxy.php?image=http%3A%2F%2Fimagizer.imageshack.us%2Fv2%2F280x200q90%2F841%2Fyjr2n.jpg&hash=c64127ee55e2ffc14e81a1b24de40d79)
![](/proxy.php?image=http%3A%2F%2Fimagizer.imageshack.us%2Fv2%2F280x200q90%2F829%2Fb2nf.jpg&hash=1551c2c4da54091f4ef4818327e8d371)
![](/proxy.php?image=http%3A%2F%2Fimagizer.imageshack.us%2Fv2%2F280x200q90%2F822%2Fqtya.jpg&hash=5a39693ed01aaf642fcc5a8a209be5fe)
Mounted the fuse holder to the factory battery bracket. The power wire was loomed and heat shrunk to be as stealth as possible.
![](/proxy.php?image=http%3A%2F%2Fimagizer.imageshack.us%2Fv2%2F280x200q90%2F819%2Ftonc.jpg&hash=f42b1dbf28ec0682d74cfe3ac61db916)
![](/proxy.php?image=http%3A%2F%2Fimagizer.imageshack.us%2Fv2%2F280x200q90%2F843%2Fnede8.jpg&hash=b030044f54ebe0b085494b341d91a84c)
![](/proxy.php?image=http%3A%2F%2Fimagizer.imageshack.us%2Fv2%2F280x200q90%2F822%2Fqfoz.jpg&hash=019a5164872ea3b0da1faf983808b99b)
![](/proxy.php?image=http%3A%2F%2Fimagizer.imageshack.us%2Fv2%2F280x200q90%2F840%2Fd3y1.jpg&hash=44a3f64b24720178cdaf967c1e536e55)
Next I ran all of the wiring following factory harnesses on each side. The wires were zip-tied approximately every 6". The power wire was ran through a gromnet I installed where the factory clutch would normally be.
![](/proxy.php?image=http%3A%2F%2Fimagizer.imageshack.us%2Fv2%2F280x200q90%2F840%2Fc1e6.jpg&hash=4d0ff8b3bbbcf23895d79657170d0103)
![](/proxy.php?image=http%3A%2F%2Fimagizer.imageshack.us%2Fv2%2F280x200q90%2F855%2Fnxn5.jpg&hash=d9de973794e80e7eba2be91cc1735011)
![](/proxy.php?image=http%3A%2F%2Fimagizer.imageshack.us%2Fv2%2F280x200q90%2F850%2Fcicj.jpg&hash=8fe72b9bd4bc101d377e0094580e2e56)
![](/proxy.php?image=http%3A%2F%2Fimagizer.imageshack.us%2Fv2%2F280x200q90%2F841%2Fyjr2n.jpg&hash=c64127ee55e2ffc14e81a1b24de40d79)
![](/proxy.php?image=http%3A%2F%2Fimagizer.imageshack.us%2Fv2%2F280x200q90%2F829%2Fb2nf.jpg&hash=1551c2c4da54091f4ef4818327e8d371)